TAINET’s SNTU 765 series is a DSL line card that enables the Ethernet & E1 data to be transmitted with the speed of 5.7/11.4Mbps over 2/4 wires. It supports up to 15 Mbps per pair of G.SHDSL.bis symmetrical data transmission under extension mode.
SNTU series is compatible with the TAINET iEAC-16 chassis. This combination is designed to work as a central office especially for long-distance Ethernet Access Service. To reduce the burden of operation/management the operator can control and monitor the remote unit via Embedded Operation Channel (EOC) by following ITU-T G.991.2.Moreover, the administrators can also easily configure all Comet series through Telnet (SSH), Web HTTP/HTTPS) or SNMP agent.
Features
- Supports EFM and TDM Dual Bearer Mode
- Point to point Ethernet and E1 extension over multiple G.SHDSL.bis copper lines
- The interfaces E1 and Ethernet can work simultaneously
- Compliant with IEEE 802.3ah EFM 2Base-TL bonding technology
- Compliant with ITU-T G.991.2 standard, TC-PAM 16/32/64/128 line coding
- 1 or 2 pairs G.SHDSL.bis with 5.7Mbps per pairs Supports extension rate up to 15Mbps over a single pair of copper
- CO and CPE mode selectable
- Automatic line rate selection with Line Probe enabled
- Front panel status LED indicators for easy monitoring
- Easy installation with console, Telnet, WEB GUI and SNMP
- Front-panel test button with BERT for easy loop diagnostic
- Provides extensive diagnostics, including loopback, G.SHDSL.bis and E1 performance monitoring
- Easy software upgrade for field-deployed units via TFTP/HTTP
- DSL line protection for data transmission
- Ethernet switching and bridging with VLAN prioritization and QoS
- Optional temperature-controlled FAN
- Optional Ethernet port surge protection
- Supports security-link
- SNTU765C is a line card type that can work within iEAC-16 chassis
Specifications
Model
- SNTU765C(Line card), 4-wire, 1 E1 G.703, 1 Ethernet port
Line Interface – G.SHDSL.bis
- Type: 4-wire
- Standard: ITU-T G.991.2, ETSI 101 524
- Bonding protocol: IEEE 802.3ah EFM 2Base-TL
- Line rate: n x 64Kbps, n=3~89 (2w), 6~178 (4w)
- Connector: 1xRJ-45
- Line coding: TC-PAM 16/32/64/128
- Impedance: 135 ?
- ITU K.21 compliant
DTE Interface – Ethernet
- Ethernet type: 10/100 BaseT
- Connector: RJ-45
- Supports 802.3x flow control
- Auto-MDI/MDIX detection
- Auto-negotiation for speed and duplex
- Full duplex / Half duplex support
DTE Interface – E1
- Data Rate: 2.048 Mbps
- Connector: RJ-45 for balanced E1 120
- (Optional external convert cable for unbalanced 75)
- Line coding: HDB3
- Framing: Framed /Framed+CRC /Unframed
- Compliance: ITU-T G.703, G.704, G.706 and G.732
- Jitter Performance: compliant with ITU-T G.823
Timing Source Function
- Synchronous and Plesiochronous dual clock mode
- Internal clock
- Received clock from the DSL line
- External clock from E1 interface
Ethernet L2 function
- Supports 802.1d transparent bridge function
- Supports Bridge filter function based on source MAC
- addresses
- Scalable per port bandwidth control (Step = 64K, up to 100M)
- 2K MAC learning address
- Ethernet packet length up to 1664 bytes
- Supports 802.3x flow control
- Provides 802.1q VLAN tagging
- Supports 802.1p QoS facility
Management
- Configuration via craft port VT-100, Telnet, WEB GUI and SNMP
- Multiple Web browsers supported: IE, Firefox, Chrome
- Console: DB9 connector (RS232C)
- Support remote management
- Independent Local and Remote loopback for E1 port diagnostic
- Support Performance Monitoring function
- Front-panel test button for easy loop healthy testing
- Front panel reset to default button
LED Indicators
- SNTU765C:
- PWR, TST, ALM, DSL, E1, ETH LNK/SPD
- Dual-colour LED for easy status monitoring
Dimension
- 84(W) x 171(D) x 24(H) mm
Operating Environment
- Operation temperature: 0oC ~ 50oC
- Storage temperature: -40oC ~ 70oC
- Humidity: 90%,non-condensing